Leak Fix Pro
Get Estimate

Water Softener Leak Repair newnan GA done right the first time

Fast, code-correct repairs for leaking softeners and brine tanks


When your softener starts weeping onto the garage floor, you need water softener leak repair newnan GA homeowners actually trust. We diagnose the leak, fix the failed fitting, valve or resin tank, and pressure-test the line before we leave. Serving Coweta County homes from Ashley Park to Lake Redwine, we handle salt-tank cracks, brine line breaks and control-valve drips the same day you call.

A close-up shot of a water droplet hanging from a stainless steel faucet, highlighting surface tension.
Licensed Licensed & Bonded
Fully Insured Insured & Bonded
24/7 Emergency Same-Day Response
Warranty Backed Workmanship Guaranteed in newnan

What Our Water Softener Leak Repair Includes

Every water softener leak repair services in newnan, Georgia call includes full diagnosis, the repair itself, a pressure test, and a walkthrough. We do not charge extra for the diagnostic if you approve the repair. Add-ons like slab leak detection or under-slab rerouting are quoted separately only when the situation calls for them.

Full Leak Diagnosis

We inspect the brine tank, control valve, bypass, inlet and outlet fittings, and drain line. A moisture meter and pressure testing gauge confirm the source. Diagnosis takes 20 to 40 minutes.

Flat-Price Repair

You get a written price before we start. Brine line swaps, O-ring replacements, control-valve rebuilds and resin tank replacements are all covered under the same flat-rate structure.

Pressure Test

After the repair, we restore water and hold 80 psi on the supply line for 15 minutes. If the gauge holds and the meter stops spinning, the leak is fixed.

Regeneration Cycle Check

We run the softener through a full regeneration cycle to confirm the control head, brine draw and drain flow all work correctly before we leave your Newnan home.

Cleanup and Haul-Off

Old parts, rags and packaging leave with us. We wipe down the area and leave your mechanical room or garage cleaner than we found it.

12-Month Warranty

Every repair carries a 12-month warranty on parts and labor. If the same leak returns, we come back at no charge. You also get a direct number for follow-up questions.

Water Softener Leak Repair newnan GA: What It Really Involves


Water softener leak repair newnan GA is a plumbing service that finds and stops leaks in a home's water softening system, whether the failure is a cracked resin tank, a split brine line, a worn O-ring in the control valve, or a corroded copper or PEX connection feeding the unit. We isolate the softener, check inlet and outlet pressure with a gauge, and trace the source with a moisture meter before we cut or replace anything. Most repairs are done in a single visit.

In Newnan, softeners take a beating. Coweta County water carries enough hardness and sediment that resin tanks, bypass valves and plastic fittings wear out years before the rest of the plumbing does. We see it constantly in SummerGrove and White Oak, where slab-on-grade homes hide the supply line under finished flooring. If you search for water softener leak repair near me in newnan and end up with a puddle instead of an answer, we can be at your door the same day.

What to Expect From Start to Finish

No guesswork, no surprise charges. Here is exactly how a water softener leak repair call runs with our team, from the first ring to the final pressure test.

01

Schedule

Call or book online — a real human picks up and confirms a 2-hour arrival window.

02

Diagnose

Licensed tech inspects on-site, then walks you through the cause and your options.

03

Fix

The job is completed to code and done right the first time — no shortcuts, no surprises.

04

Guarantee

Every job backed by a written workmanship warranty — and we stand behind it.

Tools and Methods We Use

Tools & Equipment

Moisture Meter

Confirms hidden moisture behind walls, under flooring and around the softener base before we open anything up.

Pressure Testing Gauge

Holds 80 psi on the supply line for 15 minutes to prove the repair is leak-free before we leave.

FLIR Thermal Imaging Camera

Shows temperature differences caused by escaping water, useful for tracing hidden leaks in Newnan slab-on-grade homes.

Sewerin Acoustic Leak Detection Equipment

Listens for the hiss of pressurized water escaping a pipe, ideal for confirming supply-line leaks behind a softener.

RIDGID and Milwaukee Diagnostic Tools

Used for pipe inspection, fitting prep and precision cutting on copper, PEX and CPVC lines.

Video Pipe Inspection Camera

Checks drain lines and sewer connections when softener discharge is backing up or flowing slowly.

Methods & Standards

IAPMO Uniform Plumbing Code compliance

Every repair is done to the IAPMO Uniform Plumbing Code and Coweta County inspection standards. We install backflow protection where required and document the work for your records.

Pressure isolation testing

We isolate the softener from the rest of the plumbing and pressure-test the supply line separately. This confirms the leak is in the softener loop and not the main water line.

Full regeneration cycle verification

After the repair, we run the softener through a complete regeneration cycle to confirm brine draw, drain flow and control-valve timing all work correctly.

SharkBite and Uponor PEX repair

For supply-line repairs, we use SharkBite push fittings and Uponor PEX where code allows. Both are durable, freeze-resistant and faster to install than soldered copper in tight spaces.

When to Call for Softener Leak Repair

01

You notice a wet ring around the brine tank every morning before work.

What we do: We inspect the brine line, float assembly and control valve, then repair or replace the failed part. Most morning-drip calls are a $180 to $320 fix.

→ Dry floor within one visit, and a written warranty on the repair.

02

Your water bill jumped $60 this month and the softener is running more often.

What we do: We isolate the softener, check the meter, and pressure-test the supply line. A stuck bypass valve or pinhole leak is usually the culprit.

→ Bill returns to normal within one billing cycle after the repair.

03

You are selling your Newnan home and the buyer's inspector flagged moisture near the softener.

What we do: We diagnose the source, repair it, and provide photo documentation and a pressure-test report you can hand to the buyer.

→ Clean inspection report and a closed sale without a repair credit.

04

A hard freeze cracked the brine line and you woke up to water in the garage.

What we do: We shut off the supply, replace the cracked line with freeze-resistant PEX, and check the control valve for ice damage.

→ Water back on the same day, with a freeze-rated repair that holds through the next cold snap.

How Softener Leak Repair Runs in Newnan

Newnan sits in Coweta County, where water hardness and sediment load are high enough that softeners work hard year-round. That means resin tanks, brine lines and control valves wear out faster here than in softer-water markets. Most of our calls come from slab-on-grade homes in SummerGrove, Stonebridge and White Oak, where the softener sits in the garage and any leak runs straight toward the slab. Winter freezes crack plastic brine lines. Summer heat degrades UV-exposed fittings. We size every repair to handle both. If you need a water softener system leak repair newnan GA homeowners can rely on through a Georgia summer and a January freeze, we build it that way. We also check for under slab pipe leak signs whenever a softener has been leaking for more than a week.

Neighborhoods We Serve

  • Heritage Ridge

    Slab-on-grade homes with garage-mounted softeners. Leaks here tend to run under stored items before anyone notices.

  • SummerGrove

    Larger lots with longer supply runs. We see more pinhole leaks in copper feed lines feeding the softener.

  • Historic Downtown Newnan

    Older homes with original copper and cast iron. Softener retrofits often need updated fittings and backflow protection.

  • Lake Redwine

    Newer builds with PEX plumbing. Failures here are usually control-valve or brine-line related rather than pipe failures.

  • Ashley Park

    Townhome and condo softener installs in tight mechanical closets. Access matters, and we plan for it.

Local Conditions We Plan For

  • Hard Coweta County water with high sediment

    Sediment clogs control valves and accelerates wear on seals and O-rings, so softener leaks show up years earlier than in softer-water areas.

  • Winter freezes in January and February

    Plastic brine lines and exposed fittings crack when temperatures drop below 25 degrees. We replace them with freeze-rated PEX.

  • Slab-on-grade construction common in Newnan

    Any softener leak that reaches the slab can wick under flooring fast. We check for under slab pipe leak signs on every call where water has been present more than a few days.

  • High municipal water pressure in some subdivisions

    Pressure above 80 psi stresses softener fittings and bypass valves. We test incoming pressure and recommend a regulator when it is high.

Brine Line Crack in SummerGrove Garage

Before

A SummerGrove homeowner noticed a wet ring around the brine tank every morning. The brine line had cracked from a January freeze and was dripping 30 to 40 gallons a day. The water bill had climbed $70 in one month.

After

We replaced the cracked line with freeze-rated PEX, rebuilt the control valve seals, and pressure-tested at 80 psi. The floor stayed dry through the next regeneration cycle. The following month's water bill dropped back to normal.

Maintenance: Check the brine tank monthly for cracks and keep the salt level between one-third and two-thirds full. Insulate exposed lines in the garage before the first freeze.

Before

A Heritage Ridge family heard the softener cycling every few hours and found water pooling near the base. The control valve was stuck mid-regeneration, dumping water onto the garage floor and wasting salt.

After

We rebuilt the control valve with new seals and pistons, ran a full regeneration cycle, and confirmed proper brine draw. Total repair time was two and a half hours. Water usage returned to normal within a week.

Maintenance: Run a manual regeneration once a month and listen for unusual cycling. If the unit runs more than twice a day, call us before the valve fails again.

Before

A 1950s home near Historic Downtown Newnan had a slow drip behind the softener. The copper feed line had developed a pinhole leak, and moisture had reached the baseboard and subfloor over several weeks.

After

We repaired the pinhole leak with a proper copper coupling, checked the slab with a moisture meter, and confirmed no under-slab damage. The baseboard dried out without replacement. Total cost was under $400.

Maintenance: Have copper supply lines inspected every three to five years in older Newnan homes. A $150 inspection catches pinhole leaks before they reach the slab.

Softener Problems We Fix Across Newnan

Most softener leaks fall into a handful of categories. Here are the ones we see most often in Coweta County and how we solve them fast.

Problem

Water pooling on the garage or mechanical room floor

Standing water damages drywall, baseboards and stored items, and can wick into the slab within days.

Our Fix

We isolate the softener, trace the source with a moisture meter, and repair the failed fitting, brine line or valve. If water has reached the slab, we check for under slab pipe leak signs before we close up.

Problem

High water bill with no visible leak

A slow softener leak can waste 50 to 200 gallons a day, adding $40 to $90 to your monthly bill.

Our Fix

We check the water meter with the softener isolated, then pressure-test the supply line. Most hidden leaks are a failed bypass valve or a pinhole leak in the copper feed. We repair and confirm the meter stops spinning.

Problem

Softener cycling constantly and draining to the floor

A stuck control valve wastes salt, water and electricity, and can flood the area around the unit.

Our Fix

We rebuild the control valve with new seals and pistons, then run a full regeneration cycle to confirm proper brine draw and drain flow. Most rebuilds are done in under three hours.

Problem

Cracked resin tank leaking from the base

A cracked tank cannot be patched. Ignoring it floods the floor and can damage the slab and foundation.

Our Fix

We replace the resin tank and reuse the existing plumbing loop where possible. If the feed line is also failing, we upgrade to PEX pipe with proper supports and pressure-test the whole assembly.

Why Newnan Homeowners Call Us First

Why Newnan Homeowners Call Us First

A leaking softener is not just a wet spot. Left alone, it drives up your water bill, stains concrete, and can push water under the slab. Here is what you get when you call us.

  • Stop the Water Loss

    A failed brine line or stuck control valve can waste 50 to 200 gallons a day. We shut the unit down, repair the leak, and confirm the meter stops spinning before we pack up. That alone often saves $40 to $90 on the next Newnan water bill.

  • Protect Your Slab and Floors

    Water that escapes a softener in a slab-on-grade home in Heritage Ridge or Stonebridge can wick under vinyl plank and tile. We dry the area, check for under slab pipe leak signs with a moisture meter, and flag anything that needs a slab leak repair before it spreads.

  • Same-Day Water Softener Leak Fix newnan

    Most calls booked before 2 p.m. get a same-day water softener leak repair newnan GA visit. Our trucks carry SharkBite fittings, Uponor PEX, RectorSeal thread sealant and common control-valve rebuild kits, so we finish the job in one trip instead of two.

  • Code-Correct Workmanship

    Every repair meets the IAPMO Uniform Plumbing Code and Coweta County inspection standards. We install backflow protection where required, pressure-test to 80 psi, and leave you with a written warranty on parts and labor.

Licensed, Insured and Warrantied

Licensed & Certified

  • Georgia State Master Plumber License — issued by Georgia State Construction Industry Licensing Board
  • Georgia Journeyman Plumber License — issued by Georgia State Construction Industry Licensing Board
  • Backflow Prevention Certification — issued by Georgia Environmental Protection Division approved program
  • OSHA 30 Safety Training — issued by Occupational Safety and Health Administration
  • ICC Plumbing Inspector Certification — issued by International Code Council

Verified Reviews

Google ★★★★★4.9

Fast, honest and fairly priced. They found a cracked brine line in our SummerGrove home, fixed it in under two hours, and pressure-tested the line before leaving. No upsell, no drama. Highly recommend for any softener leak in Newnan.

Yelp ★★★★★4.8

Called on a Saturday morning with water on the garage floor. Leak Fix Pro had a tech out by early afternoon. He diagnosed a stuck control valve, rebuilt it, and showed me how to check the brine tank. Fair price and clean work.

BBB ★★★★★4.9

We had a pinhole leak near our softener in Historic Downtown Newnan. The tech used a moisture meter and confirmed the slab was fine. Repaired the copper line and gave us a written warranty. Professional from start to finish.

Google ★★★★★5.0

Best plumbing experience we have had in Newnan. Diagnosed a resin tank crack, replaced the tank, and reused our existing plumbing loop to keep the cost down. Everything was dry and tested before they left.

Local Experience You Can Verify

Our technicians hold Georgia State Master Plumber and Journeyman Plumber licenses, plus Backflow Prevention Certification and OSHA 30 training. We work to the IAPMO Uniform Plumbing Code and carry ICC Plumbing Inspector Certification on staff. We have repaired softeners, water heaters, slab leaks and under-slab reroutes across Coweta County, from Historic Downtown Newnan bungalows to newer builds in The Preserve. We use RIDGID and Milwaukee diagnostic tools, FLIR thermal imaging cameras and Sewerin acoustic leak detection equipment on every job that needs them. That combination of licensing, tools and local repetition is why homeowners call us back.

  • Georgia State Master Plumber and Journeyman Plumber licensed technicians on every call
  • Backflow Prevention Certification for softener bypass and supply-line work
  • IAPMO Uniform Plumbing Code and Coweta County inspection standards followed on every repair
  • RIDGID, Milwaukee and FLIR diagnostic equipment used for hidden leak tracing
  • OSHA 30 trained crews for safe work in garages, crawlspaces and mechanical rooms
Get Started Today
Local Experience You Can Verify

Frequently Asked Questions About Softener Leaks

Real answers to the questions we hear most often from local homeowners and property managers.

How much does water softener leak repair cost in newnan GA?
Most water softener leak repairs in Newnan run $180 to $650 in 2026, depending on the failed part. A brine line or O-ring swap sits at the low end. A control-valve rebuild or resin tank replacement pushes toward the top. If the leak has damaged the slab or flooring, expect additional cost for under slab pipe repair. We give you a flat price before any work starts.
How long does water softener leak repair take in newnan?
A typical repair takes one to three hours on site. Simple fitting and brine-line swaps finish in about 90 minutes. Control-valve rebuilds and resin tank replacements take closer to three hours because we run a full regeneration cycle and pressure-test the line afterward. Same-day water softener leak repair newnan GA appointments are usually wrapped before dinner.
Can a leaking water softener be repaired in Georgia?
Yes. Almost every softener leak we see in Coweta County is repairable. Cracked brine lines, worn O-rings, failed bypass valves and leaking inlet fittings are all fixable on-site. The only time we recommend replacement is when the resin tank shell itself is cracked or the control head is obsolete. Even then, we can usually keep the existing plumbing loop and swap just the unit.
What causes water softener leaks in newnan GA?
The four most common causes we find in Newnan are high water pressure above 80 psi, sediment-clogged control valves, UV-degraded plastic brine lines, and freeze damage from a hard January cold snap. Older copper pipe and cast iron pipe feeding the softener also fail over time. A pressure testing gauge and moisture meter let us pinpoint which one is your problem in under an hour.

Other Leak Services We Handle

Need Water Softener Leak Repair newnan GA Today?

Call (470) 587-8457 and we will get a licensed technician to your door. Flat pricing, same-day service, and a 12-month warranty on every repair. If your softener is dripping right now, do not wait for the floor to buckle.

Call Now Book My Repair

call Leak Fix Pro

Reach us at (470) 587-8457 any time, day or night. We answer 24/7 for emergencies and book same-day appointments for detection and repair across newnan. If you are not sure whether you have a slab leak, call anyway and we will help you figure it out.

Leak Fix Pro


  • Address

    28 Greenville St S #581, newnan, Georgia

  • Hours

    Mon–Fri: 7AM – 7PM
    Sat: 8AM – 4PM
    Sun: Emergency Only
    24/7 Emergency Available

Call (470) 587-8457 Get Quote
Call Quote