Leak Fix Pro
Get Estimate

Thermal Imaging Leak Detection newnan GA

Find hidden water leaks without tearing up your floor


Thermal imaging leak detection newnan GA pinpoints hidden water leaks under slabs, behind walls, and beneath floors without guesswork or unnecessary demolition. If your water bill spiked, your floor feels warm, or your water meter keeps spinning, our infrared leak detection in newnan, Georgia finds the source fast. We serve homeowners across Coweta County with same-day appointments and honest, upfront pricing.

Masked healthcare worker using an infrared thermometer indoors for temperature screening.
Licensed Licensed & Bonded
Fully Insured Insured & Bonded
24/7 Emergency Same-Day Response
Warranty Backed Workmanship Guaranteed in newnan

What Our Thermal Imaging Service Includes

Every scan is a full diagnostic, not just a camera pass. We confirm findings with multiple tools and give you a clear picture of what is leaking, where, and what it takes to fix it.

Full Thermal Scan

We scan all accessible floors, walls, and ceilings with a FLIR thermal imaging camera, looking for temperature anomalies that point to hidden water leaks.

Acoustic Confirmation

We verify every thermal hit with acoustic leak detection equipment and a moisture meter, so you are not paying for a repair based on a single reading.

Pressure Test

A pressure testing gauge confirms whether the leak is on the supply side or the drain side, which changes the repair approach and the cost.

Line Mapping

A pipe locator and video pipe inspection camera map the exact line and depth, so the repair crew knows what they are cutting into before the concrete saw comes out.

Written Findings

You get a summary of what we found, what failed, and what the repair involves, with photos of the thermal screen so you can see the evidence.

Same-Day Repair Option

If you approve the repair, we can often complete it the same visit. We carry copper, PEX, SharkBite, and Uponor fittings on every truck.

Thermal Imaging Leak Detection newnan GA Explained


Thermal imaging leak detection newnan GA is a non-invasive diagnostic service that uses an infrared thermal imaging camera to locate hidden water leaks by reading temperature differences on surfaces. Water escaping from a pressurized line changes the temperature of the surrounding slab, wall, or soil, and our FLIR thermal imaging camera makes that invisible signature visible. Instead of breaking concrete to hunt for a leak, we scan first, mark the exact spot, and confirm with acoustic leak detection equipment and a moisture meter before anyone picks up a concrete saw.

Homeowners across newnan call us when a high water bill shows up with no obvious cause, when a hot spot on the floor points to a slab leak, or when the water meter spinning tells them something is leaking underground. Coweta County's mix of older homes with copper pipe and newer builds with PEX pipe means we see everything from pinhole leaks to cast iron pipe failure. If you have been searching for thermal imaging water leak detection near me, our team scans, confirms, and repairs the same day whenever possible.

How Our Leak Detection Process Works

Every job follows the same five steps. You know what is happening, what it costs, and when we will be done before we start cutting anything.

01

Schedule

Call or book online — a real human picks up and confirms a 2-hour arrival window.

02

Diagnose

Licensed tech inspects on-site, then walks you through the cause and your options.

03

Fix

The job is completed to code and done right the first time — no shortcuts, no surprises.

04

Guarantee

Every job backed by a written workmanship warranty — and we stand behind it.

Tools and Methods We Use

Tools & Equipment

FLIR Thermal Imaging Camera

Reads surface temperature differences to reveal hidden leaks under slabs, behind walls, and beneath floors.

Sewerin Acoustic Leak Detection Equipment

Listens for the sound of pressurized water escaping a pipe, confirming thermal findings before we cut.

RIDGID Video Pipe Inspection Camera

Inspects the inside of drain and sewer lines to find breaks, blockages, and root intrusion.

Pressure Testing Gauge

Confirms whether the leak is on the supply side or drain side and verifies the repair holds after we finish.

Pipe Locator

Maps the exact path and depth of underground lines so we cut in the right place.

Moisture Meter

Measures moisture content in slabs, walls, and subfloor to confirm active leaks and check for hidden damage.

Methods & Standards

Non-Invasive Thermal Survey

We walk the property with the thermal camera, scanning every accessible surface before any cutting. This narrows the search to a small area and keeps demolition to a minimum.

Multi-Tool Confirmation

No single tool is 100 percent. We confirm every thermal hit with acoustic equipment, a moisture meter, and a pressure test before recommending a repair.

IAPMO Uniform Plumbing Code Compliance

Every repair follows IAPMO Uniform Plumbing Code, from pipe material selection to pressure testing and backfill. We build it to pass inspection the first time.

Targeted Access Cutting

When a slab repair is needed, we use a concrete saw and jackhammer to open a precise access point, usually under 2 square feet, then restore with a matching concrete mix patch.

When to Call for Thermal Imaging

01

You just got a water bill that is double or triple last month with no change in usage.

What we do: We scan the slab and supply lines with a thermal camera, confirm with acoustic and pressure testing, and locate the leak the same day.

→ You know exactly what is leaking and what it costs to fix before you spend another month paying for wasted water.

02

Your floor feels warm in one spot, or you hear water running when everything is off.

What we do: A hot spot plus running water sound usually means a hot water slab leak. We confirm with thermal imaging and acoustic equipment, then repair or reroute the line.

→ The leak is fixed, the floor cools back to normal, and the foundation stays dry.

03

You are buying or selling a home in newnan and the inspection flagged possible moisture under the slab.

What we do: We run a full thermal scan and pressure test to confirm whether there is an active leak or just old moisture. You get a written report either way.

→ Buyer and seller both know the real condition of the plumbing before closing.

04

Your pool is losing water faster than evaporation explains.

What we do: We use thermal imaging on the deck and pool shell to find the failing line, then repair the pool plumbing and pressure-test it.

→ Your pool holds water again, and you stop topping it off every week.

How Thermal Imaging Works in newnan

Newnan sits in Coweta County, where the clay-heavy soil holds water against foundations and makes slab leaks more damaging than in sandier areas. Summer heat pushes supply lines to expand and contract, and winter freezes crack older copper pipe. Homes built before 1980 often still have cast iron pipe and original copper, while newer builds in SummerGrove and Lake Redwine use PEX pipe that can fail at fittings. We adjust our scan approach based on the home's age and pipe material. If you need infrared leak detection in newnan, Georgia, we bring the right tools for your specific build. We also handle same-day thermal imaging leak detection newnan GA calls for active leaks, because a slab leak in clay soil does not wait.

Neighborhoods We Serve

  • Historic Downtown Newnan

    Many homes here date to the early 1900s with original cast iron and copper. Thermal imaging helps us find leaks without disturbing historic floors.

  • SummerGrove

    Larger slab-on-grade homes with long supply runs. Thermal scans cover more square footage and often find leaks at fitting joints.

  • Lake Redwine

    Larger lots with irrigation systems and pool plumbing. We scan both the house slab and the exterior lines when the water bill spikes.

  • Ashley Park

    Newer construction with PEX pipe. Leaks here are usually at fittings or manifolds, and thermal imaging pinpoints them fast.

Local Conditions We Plan For

  • Clay-heavy soil holding water against foundations

    Water from a slab leak cannot drain away, so it saturates the soil and can shift the foundation faster than in sandy areas. Early detection matters more here.

  • Summer heat expanding supply lines

    Thermal expansion stresses pipe joints. We see more pinhole leaks and fitting failures in July and August than any other month.

  • Winter freezes cracking copper pipe

    A hard freeze can split a copper line overnight. We get calls for burst pipes and slab leaks every January and February.

  • Older homes with cast iron and original copper

    Cast iron pipe failure and copper pinhole leaks are common in pre-1980 homes. Thermal imaging helps us map the failing sections before repair.

Slab Leak in SummerGrove Kitchen

Before

A homeowner in SummerGrove noticed a warm spot on the kitchen floor and a water bill that jumped from $85 to $240 in one month. The water meter was spinning with all fixtures off. They had been told by another company that the whole kitchen floor needed to come up.

After

We scanned the slab with a FLIR camera and found the leak in a 1.5 square foot area under the kitchen island. We cut one small access point, repaired the copper pipe, and pressure-tested the line. Total repair time was 4 hours. The next water bill was back to $88.

Maintenance: We recommended a yearly thermal scan and keeping an eye on the meter when no water is running. Catching a pinhole leak early keeps it from becoming a full line failure.

Before

A 1948 home near Historic Downtown Newnan had original copper pipe and a slow leak that showed up as a damp spot on the hardwood floor. The homeowner was worried about tearing up original flooring and had put off the repair for months.

After

Thermal imaging located the pinhole leak in a 1 square foot area near the hallway. We cut a small access through the subfloor, repaired the copper section with new pipe and solder, and pressure-tested. The hardwood was saved, and the repair was done in 3 hours.

Maintenance: We suggested replacing the remaining original copper in stages over the next few years, since pinhole leaks tend to cluster in aging pipe.

Before

A Lake Redwine homeowner was adding water to the pool every three days and could not find the leak. The pool company said the shell was fine but could not locate the line leak. The water bill had climbed by $120 a month.

After

We used thermal imaging on the pool deck and found a temperature anomaly along the return line. A pressure test confirmed the break. We excavated a 2 foot section, repaired the PVC line, and pressure-tested it. The pool held water normally after that.

Maintenance: We recommended marking the repair location on the property and checking the pool water level weekly during swim season to catch future leaks early.

Leak Problems We Solve in newnan

Most leak calls start with a symptom, not a visible leak. Here are the problems thermal imaging leak detection newnan GA near me customers call us about most often.

Problem

Water bill doubled with no visible leak

A hidden slab leak can waste thousands of gallons a month and quietly damage your foundation while you wait for the next bill.

Our Fix

We scan the slab with a thermal camera, confirm with acoustic equipment, and locate the failed line. Once repaired, your bill should return to normal within one billing cycle.

Problem

Warm spot on the floor

A hot spot usually means a hot water line under the slab has failed. Left alone, it saturates the soil and can shift the foundation.

Our Fix

Thermal imaging pinpoints the leak to within a square foot. We repair the copper or PEX line through a small access cut and pressure-test before backfilling.

Problem

Water meter spinning with fixtures off

Constant meter movement means water is escaping somewhere. It could be a slab leak, an irrigation line, or a supply line behind a wall.

Our Fix

We isolate the system with a pressure testing gauge, then scan with infrared and acoustic tools to find the exact source. Most cases are diagnosed in under 90 minutes.

Problem

Soggy patch in the yard

A wet spot that will not dry out often points to a water main or irrigation line break. It can undermine the soil and lead to a sinkhole.

Our Fix

We trace the line with a pipe locator, confirm the break with thermal imaging, and repair the section with SharkBite or Uponor fittings.

Why Thermal Imaging Beats Guesswork

Why Thermal Imaging Beats Guesswork

Finding a leak the old way means breaking concrete and hoping. Thermal imaging narrows the search to a square foot or two, so you pay for the repair, not for exploratory demolition.

  • No Unnecessary Demolition

    A thermal imaging camera leak detection newnan GA scan isolates the leak to a small area, often under 2 square feet. That means one concrete cut instead of three or four exploratory breaks, and a repair bill that reflects the actual problem, not the search for it.

  • Same-Day Answers

    Most scans take 45 to 90 minutes. We confirm the leak with a pressure testing gauge and moisture meter, then walk you through findings on the spot. Same-day thermal imaging leak detection newnan GA means you are not waiting days to learn whether it is a slab leak or a supply line.

  • Protects Your Foundation

    An under slab pipe leak can saturate soil and shift a foundation over months. Catching it early with infrared leak detection in newnan, Georgia limits the water damage and keeps a small repair from turning into foundation leak repair and concrete replacement.

  • Lower Water Bills

    A pinhole leak in a copper pipe can waste thousands of gallons a month. Once we locate and repair it, most customers see their bill drop back to normal within one billing cycle. We verify the fix with a pressure test before we leave.

Licensed, Insured, and Local

Licensed & Certified

  • Georgia State Master Plumber License — issued by Georgia State Construction Industry Licensing Board
  • Georgia Journeyman Plumber License — issued by Georgia State Construction Industry Licensing Board
  • Backflow Prevention Certification — issued by Georgia Environmental Protection Division
  • OSHA 30 Certification — issued by Occupational Safety and Health Administration
  • ICC Plumbing Inspector Certification — issued by International Code Council

Verified Reviews

Google ★★★★★4.9

Fast, honest, and they found the leak in under an hour. The thermal camera showed exactly where the problem was, and they repaired it the same day. No drama, no upsell.

Yelp ★★★★★4.8

We had a slab leak in our SummerGrove home and Leak Fix Pro handled everything. They explained what they were doing, showed us the thermal images, and cleaned up after. Highly recommend.

BBB ★★★★★4.9

Professional from the first phone call. They gave us a price upfront, showed up on time, and fixed the leak without tearing up more floor than necessary. Fair pricing and quality work.

Google ★★★★★5.0

Our pool was losing water and two other companies could not find the leak. Leak Fix Pro used thermal imaging and found it in 20 minutes. Repaired it the same visit. Worth every penny.

Local Leak Detection Expertise

Our technicians hold Georgia State Master Plumber License and Georgia Journeyman Plumber License credentials, with Backflow Prevention Certification and OSHA 30 training on every crew. We work on copper pipe, PEX pipe, CPVC pipe, and cast iron pipe daily, and we carry ICC Plumbing Inspector Certification knowledge into every diagnosis. Thermal imaging is only as good as the person reading the screen, so we pair the camera with acoustic and electronic confirmation on every job. That combination is why we find leaks other companies miss.

  • State-licensed plumbing contractors with Master and Journeyman credentials
  • FLIR thermal imaging camera paired with Sewerin acoustic equipment on every scan
  • Experienced with copper, PEX, CPVC, and cast iron pipe systems
  • OSHA 30 trained crews for safe concrete cutting and trench work
  • IAPMO Uniform Plumbing Code compliance on every repair
Get Started Today
Local Leak Detection Expertise

Frequently Asked Questions

Real answers to the questions we hear most often from local homeowners and property managers.

How does thermal imaging leak detection work in newnan GA?
An infrared camera reads surface temperature differences caused by escaping water. A hot water line leak warms the slab above it; a cold line cools it. We scan the floor, spot the anomaly, then confirm with acoustic equipment and a moisture meter. The whole scan takes 45 to 90 minutes, and we show you the screen so you see what we see.
How much does thermal imaging leak detection cost in newnan?
Most residential scans run $250 to $550 in 2026, depending on square footage and how many systems we check. If we find and repair the leak the same visit, the repair is quoted separately before we start. Slab leaks, pool lines, and multi-story scans sit at the higher end. We give you the number before we begin.
Can thermal imaging detect slab leaks in Georgia?
Yes. Slab leaks are one of the most common things we find with infrared in Coweta County. A hot spot on the floor usually means a hot water line under the slab has failed. We confirm with a pressure testing gauge and pipe locator, then repair or reroute the line. Catching it early prevents foundation damage.
Who offers thermal imaging leak detection near me in newnan?
Leak Fix Pro offers thermal imaging leak detection newnan GA near me service across Coweta County, including Lake Redwine, SummerGrove, and Ashley Park. Call (470) 587-8457 and we will book a same-day or next-day window. We serve ZIP codes 30263, 30265, 30264, and 30271.

Related Services

Book Thermal Imaging Leak Detection newnan GA Today

If your water bill jumped, your floor feels warm, or your meter will not stop spinning, call us. We answer the phone, show up on time, and tell you exactly what the scan found. Same-day appointments available across Coweta County.

Call (470) 587-8457 Book a Scan

call Leak Fix Pro

Reach us at (470) 587-8457 any time, day or night. We answer 24/7 for emergencies and book same-day appointments for detection and repair across newnan. If you are not sure whether you have a slab leak, call anyway and we will help you figure it out.

Leak Fix Pro


  • Address

    28 Greenville St S #581, newnan, Georgia

  • Hours

    Mon–Fri: 7AM – 7PM
    Sat: 8AM – 4PM
    Sun: Emergency Only
    24/7 Emergency Available

Call (470) 587-8457 Get Quote
Call Quote