You can find a slab leak without breaking concrete by using acoustic listening, thermal imaging, and electronic line tracing to pinpoint the leak to within a few inches before anyone touches your floor. The concrete only gets opened at the exact spot that needs repair - or not at all if we reroute the line instead. This guide walks through how each method works, what detection costs in Newnan in 2026, and the mistakes that turn a $400 detection into a $9,000 repipe.
Why you do not need to break concrete to find a slab leak
Water escaping under a slab makes noise, moves heat, and changes the electrical signature of the pipe it is running through. Every one of those signals can be measured from the surface. That is the entire premise behind non-invasive slab leak detection: you are not guessing where the leak is, you are reading physical evidence that the pipe itself gives off.
Twenty years ago, the standard approach was to break a trench across the slab and follow the water. Homeowners paid for concrete demolition, rebar cutting, and a full slab pour - often $6,000 to $12,000 in a Newnan home - before anyone knew where the actual leak was. Today, a trained technician with the right equipment narrows the location to a 6- to 12-inch window in about 90 minutes. That is the difference between replacing one 4x4 section of floor and gutting a hallway.
Non-invasive slab leak detection is the practice of using acoustic, thermal, and electronic instruments to locate a pressurized water leak beneath a concrete slab without cutting or breaking the slab to find it. It is the standard first step before any under slab pipe repair newnan GA work begins.
How do you find a slab leak without breaking concrete?
You find a slab leak without breaking concrete by isolating the hot and cold lines, pressurizing the system, then sweeping the floor with acoustic and thermal instruments until two or more methods agree on the same spot. Agreement is the key. One tool gives you a lead; two tools give you a location; three tools give you a spot you can cut into with confidence.
Here is the sequence our technicians run on a typical Newnan slab:
- Isolate the system. Shut off the main, drain the lines, and pressurize the hot and cold sides separately. This tells us which side of the system is losing water.
- Confirm the loss. A flow meter or inline pressure gauge shows exactly how much water is escaping per hour - usually 0.5 to 4 gallons on a residential slab leak.
- Sweep with acoustics. A ground microphone picks up the hiss of pressurized water escaping a pinhole or split.
- Map with thermal imaging. An infrared camera shows the warm streak a hot-water leak leaves in the slab, or the cool spot a cold line creates.
- Trace electronically. A line locator follows the pipe itself so we know exactly where it runs under the floor - critical in older Newnan homes where the original plumbing plans are long gone.
- Mark and verify. We chalk the spot, confirm with a second pass, and only then talk about repair options.
That last step matters. If the pipe runs under a tile floor in a hallway, we may recommend rerouting the line through the attic instead of cutting the slab at all. If it runs under carpet in a bedroom, opening a 2x2 section is quick and cheap. The detection tells us which conversation to have.
The four detection tools we use in Newnan homes
Different leaks respond to different instruments. A hot-water pinhole under a slab in a 1990s subdivision off Highway 34 behaves nothing like a cold-water line break under a 1960s ranch near downtown Newnan. We carry all four tools because no single one finds every leak.
Acoustic leak detection
A high-sensitivity ground microphone listens for the specific frequency of pressurized water escaping a pipe. It works best on copper and PEX under 4 to 6 inches of concrete, and it is the fastest way to narrow a search area from a whole house to a single room. Ambient noise matters - we run acoustic sweeps before the HVAC kicks on and before the neighborhood irrigation cycles start. If you want the deep technical version, our acoustic leak detection newnan GA page covers the equipment and the frequency ranges we work in.
Thermal imaging
An infrared camera reads surface temperature differences as small as 0.1°F. A hot-water leak at 120°F leaving a copper line under a slab will warm the concrete above it by 3 to 8 degrees over a 30- to 60-minute window. That warm streak is the leak path. Cold-water leaks show the opposite - a cool spot where the escaping water is chilling the slab. Thermal is our go-to for hot-side leaks and for confirming an acoustic hit. See thermal imaging leak detection newnan GA for how we set up the sweep.
Electronic line tracing
We send a signal down the pipe and follow it with a receiver. This maps the exact path of the water line under the slab - which matters because a leak 6 inches from where you think the pipe runs is a completely different repair. Electronic tracing is also how we confirm whether a line is under a load-bearing wall, a cabinet, or open floor.
Pressure and flow testing
Before any of the above, we isolate and pressure-test the hot and cold sides separately. A 15-minute pressure hold tells us whether the leak is on the supply side at all, or whether the water is coming from a drain line, an irrigation line, or a foundation issue. Skipping this step is the number one reason homeowners pay for detection twice. Our slab leak detection newnan GA service starts with this test on every call.
What slab leak detection costs in Newnan in 2026
Typical 2026 pricing for non-invasive slab leak detection in the Newnan area runs $350 to $650 for a residential home, and most jobs land between $400 and $500. That covers the full sequence - isolation, pressure test, acoustic sweep, thermal scan, and electronic tracing - plus a written report with the marked location and recommended repair options.
What moves the number:
- Home size. A 1,400 sq ft ranch is faster to sweep than a 3,800 sq ft two-story with multiple slabs.
- Slab construction. Post-tension slabs and slabs with radiant heat require slower, more careful sweeps.
- Access. Furniture, rugs, and flooring type affect how quickly we can read the surface.
- Multiple leaks. Roughly 1 in 5 homes we test has more than one leak point. Each additional location adds time.
Compare that to the alternative: a blind exploratory cut runs $1,500 to $3,000 in concrete breaking, removal, and patching alone - before any pipe work. Detection pays for itself the first time it saves you from opening the wrong room. If you are also chasing a leak around the perimeter of the house, our foundation leak repair newnan GA team handles that side of the equation.
Signs you have a slab leak (and not something else)
The classic slab leak signature is a hot spot on the floor that never cools, paired with a water bill that jumped 20 to 40 percent with no change in usage. But that is only one pattern. Here is what we actually see on calls around Newnan:
- Warm spot on the floor. Most common with copper hot-water lines. Feels like a heating pad under the tile or carpet.
- Sound of running water when everything is off. A faint hiss or trickle at night, usually loudest near the leak.
- Water bill spike. A 2-gallon-per-hour leak adds roughly 1,440 gallons a month - about $15 to $30 on a Newnan Water bill, more if it crosses into a higher tier.
- Damp carpet or buckling flooring. Water wicks up through the slab and pad before it ever shows on the surface.
- Mildew smell with no visible source. Often the first sign in a home with engineered hardwood or tile.
- Cracks in the slab or along the wall-floor joint. Not always a leak, but worth testing.
What it is not: a running toilet, a dripping irrigation head, or a water heater relief valve that is passing. Those three account for more false alarms than anything else. We check them first because they are cheap to rule out.
Common mistakes homeowners make with a suspected slab leak
The most expensive mistake is calling a concrete cutter before calling a leak detector. Once the slab is open, you have committed to a repair location whether or not the leak is actually there.
Other patterns we see:
- Watching the water meter for two minutes. A slow slab leak moves less than a gallon in that window. You need a 30- to 60-minute test with all fixtures off.
- Assuming the leak is under the wet spot. Water travels along the vapor barrier and can surface 10 to 15 feet from the actual break.
- Skipping the hot/cold isolation. Without it, you do not know which line to chase - and you may be chasing a drain leak instead of a supply leak.
- Letting it run for months. A slab leak under a foundation can undermine soil support and lead to differential settlement. We have seen $18,000 foundation repairs traced back to a $400 pinhole leak that ran for a year.
- Hiring a detector who only uses one tool. Anyone who shows up with just a thermal camera and no acoustic or electronic gear is guessing.
If the leak turns out to be a pinhole in a copper line - the most common cause in Newnan homes built between 1975 and 2000 - the repair itself is often quick. Our pinhole leak repair newnan GA service handles those as a same-day job once the location is confirmed.
When to call a professional
Call us when you have two or more of the signs above, when your water bill has jumped more than 15 percent with no usage change, or when you can hear water running with every fixture off. Those three situations almost always mean a pressurized leak under the slab, and the longer it runs, the more it costs to fix.
At Leak Fix Pro, we run the full detection sequence - pressure isolation, acoustic sweep, thermal scan, and electronic tracing - and we mark the leak location on your floor before we quote any repair. You see the evidence. Then you decide whether to open the slab, reroute the line, or hold and monitor. No exploratory cutting, no guessing, no surprise concrete work.
Frequently Asked Questions
How do you find a slab leak without breaking concrete in Newnan GA?
We isolate the hot and cold lines, pressure-test each side, then sweep the floor with acoustic and thermal instruments and trace the pipe electronically. Most leaks are pinpointed to a 6- to 12-inch window in about 90 minutes, with no concrete opened until the location is confirmed.
What equipment finds slab leaks without breaking concrete in Newnan?
Four tools do the work: a ground microphone for acoustic listening, an infrared camera for thermal imaging, an electronic line locator for tracing the pipe path, and a pressure/flow gauge for confirming the loss. We use all four on every detection call because no single tool finds every leak.
Is non-invasive slab leak detection accurate in Georgia?
Yes - when two or more methods agree on the same spot, accuracy runs 90 to 95 percent in our experience. Georgia's clay soils and slab-on-grade construction actually help, because the slab holds the acoustic and thermal signature close to the leak point instead of letting it dissipate.
How much does slab leak detection cost in Newnan GA?
Typical 2026 pricing is $350 to $650 for a residential detection, with most Newnan homes landing between $400 and $500. That includes pressure testing, acoustic and thermal sweeps, electronic tracing, and a written report with the marked location.
Who offers slab leak detection without breaking concrete near me in Newnan?
Leak Fix Pro provides non-invasive slab leak detection across Newnan and Coweta County. We mark the leak on your floor before quoting any repair, so you can see exactly where the problem is before any concrete gets opened.
Get help with slab leak repair in Newnan
If your water bill jumped, your floor feels warm, or you can hear water running with everything shut off, we can find the leak without cutting your slab. Call Leak Fix Pro at (470) 587-8457 and we will schedule a detection visit, mark the spot, and walk you through your repair options the same day.
